MAYTAG BRAVOS QUIET SERIES 300 WASHER CODE LF

Cecilia Harsch has been writing professionally since Sep 22, Maytag Dryers. Posted on Jan 02, Pull the drain hose from the appliance drain hose or utility sink. Slide the washer forward to access the drain and water supply hoses. Go to step 5. Video How To If you need further help, reach me via phone at https: A message uL shows, the cycle stops in spin.

Guide to Wine Country Green State: Blow that tubing out and re-secure; retry with water OUT of tub so the pressure can properly build in that tubing. Depending on your model, you could see any one of these error codes. Skip to main content. Sep 22, Maytag Dryers. Short, elbow-shaped inlet hoses connect both pumps to the bottom of the washtub. Check the water inlet hoses to be sure they are not clogged or kinked.

Check the resistance sseries the pump motor. Tilt machine forward to access the bottom of the machine and the pumps. F RPS senses rotation when basket ought to be stopped. Check the pump inlet and the tub outlet bbravos obstructions. Home Guides SF Gate. Electric Dryer F73 – Questions Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US. Look inside the inlet hoses still connected to the underside of the washtub for any cloth or debris clogging the pump inlet hoses.

She writes mainly home improvement, health and travel articles for various online publications.

F8 E1 or LF or LO FL Error Code in Display – Maytag Appliances

Posted on Jan 02, awsher You can’t post conmments that contain an email address. You may also need to check the screens on the washer water inlet valve. Sep 03, Maytag Bravos 3. Sheldon Dedek Level 3 Expert Answers. Look inside the inlet opening on both pumps. Once the hoses are disconnected, you may have to scrape the sediment from the screens using a knife or sharp object. Hoses connected; water turned wide open.

  FAMILY GUY SEASON 8 EPISODE 14 PETER-ASSMENT

Check the water inlet hoses to be sure they are not clogged or kinked.

Your pf and cold water hoses are reversed on the water valve on the washer. Question about Maytag Bravos 3. Tech verified water flow looked fine, getting new controller installed tomorrow.

Use pliers to squeeze the ends of the inlet hose clamps closest to the pumps.

Is the drain pf clogged, or the end of the drain hose more than 96? Long Drain Ld flashes when the water level does not change after the drain pump is on.

Tilt the Bravos washer forward and let the front of washeg appliance rest on the floor so you can reach the drain and recirculation pumps. What do I need to do or what is wrong?

Is the drain hose installed properly? Helpful 0 Not Helpful Flag. Note that there is a tab on the outlet connector that fits into a slot in the hose. Plug the harnesses back into the pumps and snap close the wire covers. Short, elbow-shaped inlet hoses connect both pumps to the bottom of the washtub. Then press Power again to restart the washer.

  SAKI ZENKOKU-HEN EPISODE 12 ENG SUB

It’s about 3 years old.

How to fix LF error code on maytag bravo washer please answer ASAP? (:?

Click “Add” to insert your video. This draining process takes approximately minutes to complete. Allow washer to complete this cycle before disconnecting power again. Other options work like rinse and spin and drain and spin, but it will not fill and the machine sits there.

Verify that the water is turned on. Press the power button, and the washer will start a drain routine which takes approximately 8 to 10 minutes, during which time the pump will run continuously.

The control will not accept any input during this time. Unplug your Maytag Bravos washer from the electrical outlet. Customer Service Newsroom Contacts.

You can’t post answers that contain an email address. See Figure 1, page I think there was an F73 or F93 error message but we did not write it down. Aug 28, Maytag Bravos 3. Please assign your manual to a product: Cecilia Harsch has been writing professionally since Two hose clamps hold the inlet hoses to the washtub and to the pumps.